® Rapid-deployment PRO Beam NEW!

highest performingXR-2500 circuit board
– top image shows the PRO Beamset Battery option
– bottom image shows an image of the battery
Download 4-Zone receiver User manual Click to Download
Product Highlights
  • Battery powered (Non-solar)
  • Invisible beam up to 250m long!
  • 700-1400m Wireless Range
  • Waterproof external battery packs
  • Supplied with green alignment laser
  • 3 Year Warranty, including batteries
4-Zone Receiver Highlights
  • Monitors up to 4 PRO (or smaller) beam-sets
  • Supports optional 4G text alerts
  • Adjustable alert “beep’ volume
  • Optional ‘police’ strobe lights or other deterrent
Will it work for me and how much?

Freephone NZ: 0508 727 223 / Australia: 1800 456 736

Send us an enquiry

Basic Overview

This new battery-only version of the PRO beam-sets is intended for rapid-deployment on construction sites, civil works sites, hazardous sites, large outdoor venues, or any temporary or constantly changing situation.

® PRO beam-sets project a powerful detection beam over a distance of more than 260m (this version) allowing intruders or vulnerable people to be detected entering or wandering around on a site before they cause any damage or harm themselves.

  • Reduce the cost of security guards
  • Rechargeable 5000mAh waterproof battery packs (easily swapped)
  • Supplied with laser alignment tool
  • Beam distance selected by 10-position selector (35-250m range)
  • Connect a text messaging (SMS) module to the base receiver to send alert notifications to guard or monitoring company
  • Base receiver can drive “police” strobe lights (psychological deterrent)
  • Available only in XR-LoRa protocol (long wireless range version)

How the detection beam works …

The image below shows how the projected IR beam has a divergence angle that ensures the receiving beam-unit (called the “Beam-communicator”) is always “seeing the projected spot” unless poorly aligned. Some movement is tolerated because of the beam divergence. In reality the cone-shaped beam does not have a sharply defined boundary – the beam gradually weakens radially outward from the centre until it is too weak to be received.

Beam signal range

Simple 5 Step Beam installation procedure.

Simple 5 step instal process

3 important installation requirements …

(1) Flat ground.
PRO beam-sets work reliably over flat ground. Undulating ground can create detection anomalies where the detection beam is either too high, or too low to the ground.

(2) Rigid Mounting
If the beam-sets are going to be installed in the same location for a long time, we recommend mounting them on a solid fence, wall or on quality hardwood or laminated ply post such as Prolam so they remain aligned indefinitely.

(3) Mounting height
Beam-sets should be mounted between 1000-1200mm above ground (900mm minimum) to minimise “ground scatter”.

Specifications
Pro Series Beam Set
Type of Beam Active Photo-electric Infra-red
Maximum Detection Beam distance 250m
Maximum Wireless range Refer to XR series reference guide
Diagnostic reports YES
Diameter of IR beam 65mm
Beam alignment method Laser alignment tool
Modulation Type Gaussian Frequency Shift Keying (GFSK) and LoRa protocols depending on version
Radio Frequency 458.550 MHz
RF Output Power 80-100mW
Average Power Consumption per Beam Unit 10mW
Battery Voltage 3.7V (charges to 4.2V approx.)
Battery Capacity 5000mAh
Protective Metal Housing Powder-coated stainless steel
Weather Resistance
  • Poly-Carbonate, IP66 rated Enclosure
  • Fully weather-proof
  • Ant-proof
Dimensions – Millimetres W80 | D88 | H120
Warranty 3 Years
Base Receiver
Two-way Radio Supervision YES
On-board Diagnostics YES
Maximum Number Of Supported Beam-Sets 4
Volume Adjustment YES – Adjustable Volume (can also be muted)
Adjustable timed outputs 4-zone outputs
Number of timed outputs 4
Timed output range 4 – 120 seconds
External Pager output YES
4G Communicator Port YES
Frequency 458.550Mhz
Power Requirements 12V DC 500mA
Dimensions – Millimetres W75 | D119 | H30
Warranty 3 Years